Centsys D5 Spezifikationen PDF herunterladen

Fit endstops capable of stopping the gate at rated speed

Make H>h to ensure gate will not jump over endstop as shown

above

Ø16mm

Endstop

Endstops

1. D5-Evo controller

2. Courtesy light fuse

(3A F/B)

3. Gate mounted origin

marker

4. Origin marker bracket

5. Origin sensor

6. Side covers

9. 1 x 12V 7.2Ah battery

10. Switch Mode 2A charger

11. Manual release access

door

Foundation plate

Motor fuse (30A ATO)

6. D5-Evo identification

3. Icons used in this guide

2. Important Safety Instructions

This guide is designed specifically for installers who are familiar with

the installation of standard sliding gate motors, but do not know the

specifics of the D5-Evo.

The D5-Evo is a domestic and light-industrial operator designed to

open and close sliding gates weighing up to 500kg. A custom designed

gearbox moulded from robust engineering polymers, coupled to a

powerful 12V DC motor, provides fast and reliable automation for

entrances to homes and small housing estates.

Please do not proceed with the installation until you have

read and fully understand the Safety Instructions

included in your product packaging

The Safety Instructions are also available on

www.centsys.com.au

1. Introduction

4. General description

This icon denotes variations and other aspects that should be

considered during installation

This icon indicates tips and other information that could be

useful during the installation

This icon indicates warning, caution or attention!

Please take special note of critical aspects that MUST be

adhered to in order to prevent injury

7. Preparation of site

General considerations for the installation

For comprehensive information, please refer to the full installation

manual available for download on www.centsys.com.au

Install the gate operator only if:

It will not pose a hazard to the public

There is sufficient clearance to a roadway and/or public

thoroughfares

The installation will meet all municipal and/or local authority

requirements once completed

The gate mass, length and application is within the operator

specifications

The gate is in good working order, meaning:

That it moves freely

Does not move on its own if left in any position

It can be installed to have sufficient clearance between

moving parts when opening and closing to reduce the risk of

personal injury and entrapment

Pushbuttons or keyswitches, when required, can be positioned

so that the gate is in line of sight of the operator

Make sure the gate mass,

starting - and rated-pull-force

limitations are not exceeded.

Guide-rollers must ensure that

the gate is held vertically through

the entire length of the gate

travel. For improved safety fit

additional support posts to

prevent gate from falling over

if guide rollers fail.

Ensure that the gate

cannot be lifted off the

motor pinion with the

anti-lift bracket fitted

Pull scale

Guide-rollers

Additional

support post

GAP<5mm

Typical anti-lift

arrangements

9. Cabling requirements

It is a 12V DC battery operated unit with the following limitations:

Operator push force - starting 30kgf

Operator push force - rated 17kgf

Gate mass – maximum 500kg

Gate length – maximum 100m

Maximum numbers of operations per day 150

5. Technical specifications

8. Lubrication

1. Lift the cover of the

operator.

2. Remove the battery so that

you can gain access to the

coloured filler plug.

3. Remove the coloured oil filler

plug by levering it out with a

screwdriver.

4. Empty the contents of the oil

bottle into the gearbox

(80ml).

5. Refit the coloured oil filler

cap.

Put 80ml oil

in here

Oil specificationsCEN

product code:

OIL80ML0X0/H

Castrol SAF-XO 75w-90

Synthetic Final Drive

Lubricant

Do not attempt to run the operator without first filling the

gearbox with lubricant

Legend

1. 220-240V AC mains cable via double pole mains isolator switch

(3 core LNE 1.5mm SWA)

Optional wiring (all cable is multi-stranded):

2. Intercom cable from motor to dwelling (n1 + 6 core 0.5mm )

3. Intercom cable from motor to entry panel (n2 0.5mm )

4. Safe Close and

Safe Open: Recommended infrared safety beams

(3 core 0.5mm )

5. Trg: Access control device (3 core 0.5mm )

6. Ped: Optional pedestrian keyswitch (a) OR keypad

(b) (3 core 0.5mm )

7. Trg: Optional external radio receiver (3 core 0.5mm )

8. Light: Optional pillar lights (3 core LNE SWA, size

according to power requirements)

n1 = number of cores required by intercom

n2 = number of cores required by intercom

Possibly increase cable thickness if pillar lights are installed

Type of cable must adhere to municipal bylaws but typically SWA

(steel wire armoured) cable is recommended. The armouring

provides excellent screening, which gives better protection against

lightning – earth one end of the screening)

Allows for all features such as pedestrian opening, status LED, etc.,

to be operated from the intercom handset inside the dwelling.

Number of cores and type of cable could vary depending on brand

of access control system being used

For optimum range, an external receiver can be mounted on the

wall

10. Manual operation

D5D5

evo

evoevo

1. Insert the camlock key and

rotate it 90° clockwise.

This will allow for the removal

of the cover, as well as for the

rotation of the release

thumbwheel.

Do not remove the

thumbwheel. Removal of

the thumbwheel may

result in water entering

the gearbox and the

warrantee will be void

Disengage

gearbox/drive

D5D5

evo

evoevo

D5D5

evo

evoevo

1. Rotate thumbwheel anti-

clockwise until thumbwheel

feels loose in the hand. Make

sure that the manual

override access door can be

closed.

2. Slide gate until gearbox/drive

engages. Never run the

motor before the unit is

engaged.

Re-engage

gearbox/drive

Ensure that all the standard considerations for a quality

gate installation are adhered to as detailed in

CENTSYS' detailed installation manuals. These must

include:

11. D5-Evo operator installation

Correct access in and out of the premises

Endstops are mandatory and must be capable of stopping the

gate at rated speed

Guide-rollers and anti-lift brackets are correctly fitted

The gate mass, starting- and rated-pull-force limitations are not

exceeded

The D5-Evo is positioned correctly and does not protrude into the

driveway

Oil filling procedure

2. Rotate thumbwheel

clockwise until gearbox

releases and gate can be

moved manually.

3. If the gearbox must be left in

manual mode for an

extended period of time for

whatever reason, it is

recommended that the

access door is locked. This

secures the cover and

prevents access to the inside

of the unit, which contains

high voltages. It also

prevents theft of any

components and provides full

protection from the

elements.

B: Above pinion - Steel rack

* Includes 3mm clearance required

between rack and pinion

32 - 50

(Recommended to

allow for adjustment)

146*

Foundation

plate

Flat bar welded to

foundation plate and rail

1. To ensure operator does not

protrude into driveway, install

base plate at least flush with

the driveway entrance.

2. Determine a suitable position

and vertical height for the

operator by considering

Figures A, B and C.

A: Above pinion - Raz rack

32 - 50

(Recommended to

allow for adjustment)

163*

Foundation

plate

Flat bar welded to

foundation plate and rail

* Includes 3mm clearance required

between rack and pinion

Locate operator

position

Evo

EvoEvo

www.centsys.com.au

0.07.B.0009 D5-Evo Mechanical

Pocket Guide-5Jul2012

D5-Evo Pocket mechanical

installation guide

LIGHT-

INDUSTRIAL

SLIDING GATE

OPERATOR

1 2

Inhaltsverzeichnis

Seite 1 - OPERATOR

Fit endstops capable of stopping the gate at rated speedMake H>h to ensure gate will not jump over endstop as shown aboveØ16mmhHEndstopEndstopEndst

Seite 2 - 13. Installation handover

Mounting the originmarker1. Close the gate completely.2. Mount the origin marker to the rack a minimum of 500mm from the origin sensor.3. For steel ra

Kommentare zu diesen Handbüchern

Keine Kommentare

Centsys D5 Spezifikationen

Stöbern Sie online oder laden Sie Spezifikationen nach Toröffner Centsys D5 herunter. Centsys D5 Specifications Benutzerhandbuch

Inhaltsverzeichnis

Kommentare zu diesen Handbüchern

Verwandte Produkte und Handbücher für Toröffner Centsys D5